DIY Hollow Lures with Dollar Store UV Resin: Prototyping for Mass Production

English

I bought a UV LED resin curing light at Daiso for just 300 yen.

My local Daiso was sold out, but they had tons of them at the Hakata Station Bus Center shop. It works surprisingly well!

The resin is 300 yen for 20g. According to my daughter, 100-yen store resin tends to discolor and stay tacky, so it's not the greatest; she claims a brand called "Masaru's Tears" (Masaru no Namida) is just as cost-effective and much better.

Her top recommendation is "Drops of the Moon" (Tsuki no Shizuku). I guess it has superior clarity? But since I'm going to paint over it anyway, discoloration isn't really an issue for me.

With this setup, my dream plan of crafting custom hollow resin lures is finally underway.

I'm using a silicone popper mold I made previously. The original master was a hand-carved wooden lure—the Giant PopMax Mark III—that I had gifted to an older friend back in the day. With UV resin, you can build it up layer by layer, almost like a manual 3D printer. Since the two halves will be joined together, I start coating near the seam line at the bottom, though gravity naturally pulls a lot of it down along the sides.

Oh, nice! It cures instantly. And no nasty solvent smell, either.

The bottom section was looking a bit thin, so I stood the mold upright before blasting it with the UV light. Originally, this mold was designed to be clamped shut and injected, but the resin never flowed properly and kept failing. Doing it this way allows me to build it up gradually—plus, since each layer cures in just a minute, I can keep working in quick one-minute cycles.

Here's what it looks like out of the mold. Because it's Daiso resin, it's slightly sticky... but spraying it down with parts cleaner eliminates the tackiness completely! Daiso's biggest drawback: officially solved.

Now, I smooth out the mating surfaces with sandpaper to get them nice and flat.

Time to build the weight chamber. I use Oyumaru (moldable craft plastic) to build a dam, pour in some UV resin, and cure it. I positioned the chamber toward the rear end, just like a diving pencil lure designed for kingfish. This thing is going to cast like a bullet! Maybe because I shaped it with a steel file, it took on a slightly brownish tint.

All done with that part. Man, UV resin really is incredible.

Lately, I've been really into prop baits, so I decided to turn this into a "Popper-Prop" hybrid. I found some worm props at the local tackle shop.

Here they are. I disassembled the unit, widened the hole using a drill bit and a file, and tweaked the prop blade angles with pliers. Then I added metal cup washers to the front and back—also picked up at the tackle shop.

If this section is too thin, water might seep in. To beef it up, I used Daiso's Oyumaru to create a cavity and filled it with UV resin. Drilling holes later is a hassle, so I embedded the screw eye right from the start and cured it in place. Getting it perfectly straight is tricky! Once cured, you can still unscrew and remove it with a simple twist.

Next up is the belly screw eye. Just like before, I created a base using Oyumaru, poured in the UV resin, and hit it with the light. I also dropped in two metal bearings to give it a nice, crisp rattle.

I checked the seam alignment and sanded it down once more, then applied UV resin along the joint before pressing the halves together. Once joined, I brushed on another coat over the outside seam.

Hit it with the UV light... It's amazing how, even when adding extra resin in layers, it forms such a rock-solid molecular bond that it looks like it was molded as a single piece from the very start.

And there you have it: the Giant PopMax Prop Popper! It looks just like a prototype straight out of a lure manufacturer's lab.

Leave a Reply