Giant PopMax-Plopper: Pre-Production Prototype Unit #2

English

When I told my usual fishing buddies that I was doing a pre-production trial run, an order came in right away! The senior angler who ordered owns the very first prototype of this mold—a fun, multi-colored piece painted with an airbrush in green, black, and orange. This time, however, he requested solid red... I'm building this virtually in parallel with Unit #1.

I thought about laying down a silver base with clear red on top to match the fiery Soul Red on a Mazda Miata, but...

I decided to use this build as an experiment to see if I could tint UV resin directly. First, I made a clear outer shell. After curing that, I layered in the tinted UV resin—can't recall if it was clear red or solid red—and cured it bit by bit.

Next, I set the lure eyes in place and secured them with UV resin all around.

Since silver underneath clear red creates that gorgeous Miata Soul Red, I quickly tried applying silver with a paint marker. Well... it didn't really do anything.
For the tail section, a prop will be attached, so I filled it with resin so I could screw in an eyelet later. I reinforced the head the same way. Even though it's clear resin, the red reflects through, making the entire body appear red. In the photo, I thought the weight was a 5.5g pachinko ball, but... cue the trial and error.

Adding color pigment to UV resin causes a huge change: it stays soft right after curing. It gradually hardens over time, but the first half I made warped as it cured, so I scrapped it and started over. It's best to leave it in the mold for a few days until it fully cures.

With this weight, it's 6g.

And combined with the pre-assembled body, it comes to 16g.

This other weight is 9g, bringing the total to 20g. Since my target was around 20g overall, I decided to go with this one.

On top of that, I added a metal ball in the back to act as a rattle.

From top to bottom: Giant PopMax-Plopper Unit #0, Unit #1, and Unit #2.
Right after this, I took it along with Unit #1 for a swim test and discovered they both sink! I had assumed the resin used to join the halves, two more eyelets, two treble hooks, and the prop would just be negligible margin of error... Big mistake. It was way too heavy.

By the way, during a later swim test at Kuboshiro Dam, Unit #0 snapped off on a cast and flew away... I could see something floating far in the distance, though it might have just been a dead leaf. There was no wind, so it wasn't moving at all. To rescue it... I spent an entire hour casting Unit #2 until I finally hooked and retrieved it. Unit #0 floated, but Unit #2 was a sinking failure, so if my line snapped again, there was zero chance of recovering either. Still, I figured if a fish hit it, that'd make a great story, and it gave me a chance to check the action anyway! Unit #1 had extra facial details sculpted on to give it a rugged look, so I was determined to save it. (Unit #0 ended up getting lost later at Kawauchi Disaster Prevention Dam, though...)

Time for another weigh-in to adjust the balance. Unit #0 weighs 20g fully rigged with hooks and the prop.

The hooks and prop weigh 3g together.

I cut open the belly to remove the internal weight. Without the weight, but including all other hardware, the total comes to... 17g.

So, I went with a size 0.5 (2g) weight plus two steel rattle balls. That should bring the total weight right to 20g. The bumpy texture on the belly comes from old carving chisel marks on the silicone mold. I thought it gave it character, but it gradually disappeared as I finished the surface... I inscribed the recipient's code name, "TOK".

Afterward, I tested clear-coating the surface with low-viscosity UV resin, but the results weren't great. Even with clear resin, the red reflection washed out the surface details... The final surface was polished up with rubbing compound.

Since this is Unit #2, I painted a "2" on it. I coated over it with UV resin, but it looks like it's peeling a bit... The white specks are just compound caught in tiny pinholes in the resin. And with that, it was delivered! Looking at it now, the details are definitely a bit soft and rounded.

Leave a Reply