Custom DIY: Converting a 2-Piece Bass Rod into a Multi-Piece Travel Rod

English

I took a 2-piece spinning bass rod that I probably bought around 20 years ago and converted it into a 4-piece rod by cutting each section in half.

Lately, for bass fishing, I've been using a 4-piece baitcasting rod that was cheap but has become a favorite. For spinning, I often use an 8.6-foot, 2-piece eging rod for long casts, but whenever I'm gunning and running along the shoreline with that eging rod tucked into my backpack, it constantly gets snagged on trees. I thought about buying a cheap short rod, but then it hit me: why not just modify the one I already have? However, since that eging rod is a favorite and recently became my son's go-to, using it would be too risky—so I decided to use the bass rod instead.

I originally bought the baitcasting reel so I could go black porgy drop-shotting on my way home from work. While it was in my bag, the tip broke, so I modified it with a titanium tip. Then the grip started peeling, so I just replaced it with a Fuji grip. I've grown even more attached to it. It's an OGK OKAPPARI. I bought it for just under 4,000 yen at a tackle shop near my parents' house a while back. The other day, I saw the spinning version at the same shop and was tempted... I want to build one myself!

I started planning where to make the cuts. I figured it would be best to cut right near the existing thread wraps since the blank is stronger around there, eliminating the need for extra reinforcement. For the top section, just below the guide thread, and for the butt section, just below the decorative thread. These spots are near the middle, and making the tip section shorter works out nicely. Otherwise, it would snap inside my backpack. By the way, I also converted the tip of this rod to titanium a long time ago, so that part will never break. The second section ends up a bit too short, but I decided to go with it without worrying too much about length balance. I marked the spots with a silver paint marker.

The focus is a bit off, but this is while I was cutting it. Since I wasn't using it anymore, I had no hesitation. I cut it with a 100-yen-shop saw. It's surprisingly hard.

The method for joining the pieces is a spigot ferrule (inro-tsugi); when splitting a single rod, this is pretty much the only way. The material comes from broken rods. When I visited my parents' house, my dad's unwanted rod was stuck upright in the garden flowerbed, so I brought that back along with a rod tip I found and picked up at the sea once. Both are super long, floppy rods for float fishing, so I'm a bit worried about the strength. To compensate, I'm going to insert an even smaller piece of the tip inside the joint insert to boost the strength. This is my first time doing this. I looked up a few guides, and that's what they recommended.

I inserted the spigot joint part into the cut rear section of the rod. I marked it with a paint marker where it bottoms out and... wait? The tip didn't go in as far as I expected. I imagined it would go in almost all the way until it touches, but maybe the ferrule has too little taper? Or is it warped? The one on the left is under construction, and the one on the right is the OGK 4-piece. They make the joint quite long, don't they? If I make it that long, that section might become too stiff and won't bend properly, so I'll make it a bit shorter than that.

Comparing them... I wanted to insert the tip a bit deeper, so I tried various trial-and-error methods like shortening the spigot and sanding down the taper.

Determining the final length on the tip side. The paint mark in the middle and the black area between them will be the exposed section. The lower side will have thread wrapped around it, so the exposed part will be slightly reduced. I decided on the depth of the paint marks at both ends based on the gut feeling that this insertion depth would give a good bending curve.

For the binding/reinforcement, I used PE line. I wrapped it, painted it with a black paint marker, and cured it with UV resin. After making another one, I realized that painting it black prevents the resin from soaking into the thread, which seems bad for strength. Should I redo this one...?

It's not finished yet, so it looks messy... This is what the connection looks like.

In the same way, I'll make the butt side by matching the length and strength. Since UV light can't reach the inner adhesive, I'm using instant glue (super glue) for that part.

I secured this part too using PE line and UV resin as a binding, but since adding paint to make it black compromised the strength, I redid it and left the paint out.

It's done. As for the bending curve... the joint sections are a bit weak.

Lining up the butts, the length looks like this. It's long enough to protect the number 1 top section with another thicker section. Though, since it's titanium, it's actually invincible. I made the butt section a bit longer to protect the number 2 section, but cutting it shorter might be fine too.

Originally, the lure weight rating was 3/8 oz = 10g, but that spec is probably gone now—maybe I'll write 8g or something. Also, I peeled off the label/sticker-like things here and further removed them by sanding with sandpaper.

It originally had a silver paint finish, but as the carbon pattern started showing through, it ended up looking surprisingly high-end. The piece on the far right is the sanded part. The middle piece right next to it is still the un-sanded silver. It's a bit hard to tell in the photo, though... Should I sand the whole thing?

That's all.