Making the Propeller Assembly for a DIY Motorized Kayak
The conceptual image of the overall design looks something like this.

The Propeller Shaft Section

Here is what the backside of a 2-horsepower propeller looks like. I need to machine a matching component to transmit rotational force, plus a cotter pin mechanism at the tip to prevent it from slipping off.
This is the actual machining design.

The key to amateur design is minimizing machining and making things work with readily available materials. Even professionals need to keep this perspective in mind for cost reduction. Nowadays, since people design using 3D CAD, they sometimes end up drawing whimsical blueprints that are practically impossible to build.
Materials
- 10mm dia. aluminum rod (cut to 50mm) — Material: 1m 10mm dia. aluminum rod, 734 yen from Handsman
- 3mm x 20mm snap pin: Handsman
- 6mm x 70mm shaft: Stainless steel parallel pin, 6mm x 70mm, Handsman (around 280 yen?)
- 40mm cotter pin: Handsman, and I also had some in stock at home. Tens of yen.
- Pulley: Handsman sliding door roller, 36mm with 30mm inner diameter, 148 yen.
Machining the Aluminum Shaft
I cut a 50mm piece from a 1-meter, 10mm-diameter aluminum rod and drilled a 6mm x 30mm hole right in the center.
My memo says, "Next time, make it 20mm." That was probably because I wanted to make the total length—or rather, the rear end—a bit longer. Ah, wait, I remember now. The real reason was that drilling a straight hole as deep as 30mm was tough, and fitting the shaft into it was also super tight.

Drilling right in the center is a huge pain. If it's even slightly off, the propeller will wobble violently.
Having a lathe to spin the material while drilling dead center would make it a breeze, but all I've got is a drill and a drill guide (for woodworking). Using this setup, I clamped the aluminum rod into the drill side......and rotated the material side instead.When I looked up the price of a lathe chisel, it was shockingly expensive, so I gave up on that idea. Instead, I took a drill bit I had on hand, stuck it into the shaft of a 100-yen-shop screwdriver to use as a cutter, and built a wooden fixture fixed to the underside of the drill guide. I drilled a 10mm hole, poked the screwdriver-bit setup through it, and pressed it against the spinning aluminum rod to carve it down.

By the way, while working on this motorization project, I realized I wanted a workbench for my balcony. I had just dismantled a bed, and its slatted base was sturdy and perfect, so I built a desk out of it. To accommodate projects like this, I made part of the tabletop easily removable. This lets me use the drill guide in its normal orientation with the drill bit poking up from the bottom. In the future, I want to get compact tools like a lathe or circular saw, or maybe even build them myself.

I started drilling with smaller bits and worked my way up—I don't remember exactly how far I took that step, but once a pilot hole of a certain size is made, the hole itself acts as a guide. So for the final step, I attached a 6mm drill bit to the drill and bored it out normally.
I managed to drill the hole right in the center amazingly well.

The smaller shaft is a stainless steel parallel pin. Every time I see these at Handsman, I fall in love with them. I used to think threaded bolts were the most versatile and accessible type of axle, but a threadless pin like this has so many potential uses.

This photo shows the almost-finished assembly, machined to fit a standard 2-horsepower propeller.
I inserted the 6mm shaft into the hole in the aluminum shaft. It was an insanely tight fit. I ended up having to hammer it in, which slightly bent the aluminum shaft... I figured trapped air got compressed and created resistance. It probably would have helped to drill the cross-hole for the anti-rotation pin first to let the air escape. Also, reducing the depth from 30mm to 20mm would have been smart. This thing is now stuck in there permanently.
As for drilling the hole for the anti-rotation pin, since it's on the curved surface of a cylinder, I had to file a flat spot first so the bit wouldn't slip. Initially, I planned to insert pins from two opposing directions, making the hole in the shaft non-through so they would just catch on it. However, trying to drill straight holes from two directions turned out to be surprisingly insanely difficult, and it ended up looking a bit botched. My guard was down. To drill straight, I should have gone all the way through from a single direction. Ideally, I should have drilled all the way through the aluminum first, then inserted the small shaft, → drilled straight through again. Miscalculating and getting the shaft permanently stuck was another blunder. Strength-wise, though, a single through-pin feels pretty solid.Lots of lessons learned here. I'll definitely apply them the next time I build one.
The necked-down groove at the tip is designed so that a cotter pin inserted from outside the propeller will catch in this recess and keep it from sliding off. I shaped this part almost entirely by hand with a file. Aluminum is wonderfully easy to carve.
Making the Pulley
Handsman only seems to sell massive real pulleys, and they're expensive. While I could have ordered from MonotaRO or somewhere similar, I found a great alternative right at Handsman!

It's the Yokozuna sliding door roller I've mentioned a few times. You can buy them for around 150 yen. They come in a few varieties depending on the material—they had nylon, polypropylene, and I think even polycarbonate? What was this one made of again? I chose it because it felt like it had just the right amount of strength. If it doesn't hold up during a test run, I can always swap it for another. They even have stainless steel ones if needed. I destroyed the center axle with a drill just to salvage the wheel part.

I grabbed three different sizes to test out. I'll use the largest one for the propeller pulley.

To keep it from spinning freely on the shaft, I drilled a side hole and tapped it for a screw. I made a custom jig just to hold it steady for this—literally just a wooden block with a hole drilled in it, held together with screws.

The drill bit tends to bite in suddenly, making the pressure hard to control. I secured it with an M3 screw. Whether it's a failure or just practice, I did it in two spots. This photo was taken before jamming the shaft into the aluminum rod.

By combining all the parts made so far, the propeller shaft assembly is complete.

Now for the design of the propeller body housing. I haven't fleshed it out completely, but it looks something like this: a 10mm or 5mm thick base measuring 30mm x 200mm, with an extra plate added to the bottom for the bearing. For the top, I want something that's easy to remove and set up.

I want to mount the propeller right around here, so roughly a 200mm span should do.

Look at that—this wooden board fits like a glove.

For the pulley belt, I initially planned to cut and splice a length of raw rubber cord, but the adhesive strength wasn't cutting it. While wandering around Handsman looking for alternatives, I found a ready-made O-ring of the perfect length. Is it a P150? Meaning roughly 150mm inner diameter? Probably. I'll calculate the exact size later based on the base length and pulley pitch.

Since the material for the final base is pricey, I'm using a wooden board for this prototype to test whether the concept actually works.

Put everything together and... oh man, looking good! I think this is actually going to work. That's it for the propeller section for now.


